This light weight tailgate cap adds that extra protection for saving your tailgate from rubbing of a topper / canopy / shell window. PLEASE READ FULL DESCRIPTION
This cap will need to be riveted or screwed onto your tailgate, there are 5 ( 1/8” ) pre drilled holes
LIGHT DUTY USE ONLY! Installer may need to tweak/bend the cap based on fitment!
Features:
CNC Plasma Cut, CNC Bent
Made from 5052 Aluminum .050” Thick
Raw Uncoated, unfinished. Expect Tooling marks and possible light scratches
NO HARDWARE INCLUDED!
Vehicle Fit: Toyota Tacoma 1995 - 2004
PLEASE READ ALL OF THE FOLLOWING BEFORE PLACING YOUR ORDER!
This kit takes the headache and multiple trips to the parts store out of the equation! We did all the hard work for you so its as simple as a 30 min install!
You will be required to drill 4 new holes in the fenders for the lower mounting brackets using the supplied template, as well as 4 new holes on the sides of the hood hinges.
This kit gets 29" of lift
Complete Kit Features:
CNC Plasma Cut, CNC Bent
X4 11g P+O steel brackets
X1 18g steel Drill template
X2 50lb Gas Struts
Hardware Kit ( x4 m6 bolts, x4 m6 washers, x4 m6 nuts, x4 m5 bolts, x4 m5 nuts, x8 m5 washers, x4 ball studs, x4 5/16 nuts, x4 5/16 washers )
BRACKETS ARE RAW UNCOATED, INSTALLER NEEDS TO COAT BRACKETS TO AVOID CORROSION!!
Bracket Kit Features:
CNC Plasma Cut, CNC Bent
X4 11g P+O steel brackets
X1 18g steel Drill template
Hardware Kit ( x4 m6 bolts, x4 m6 washers, x4 m6 nuts, x4 m5 bolts, x4 m5 nuts, x8 m5 washers )
BRACKETS ARE RAW UNCOATED, INSTALLER NEEDS TO COAT BRACKETS TO AVOID CORROSION!!
BRACKET KIT DOES NOT INCLUDE GAS STRUTS NOR BALL STUDS!
We recommend 14” extended struts that are at least 40lb capacity per strut
DISCLAIMERS:
THIS KIT MAY REQUIRE RELOCATION OF FACTORY COMPONENTS!!
THIS KIT IS DESIGNED FOR FACTORY STEEL HOODS!! USE ON FIBERGLASS, CARBON FIBER OR OTHER
LIGHT WEIGHT HOODS MAY CAUSE DAMAGE!!
ROHDE FABRICATION DOES NOT WARRANTY GAS STRUTS SUPPLIED WITH OUR KITS!!!
Vehicle Fitment: 1986 - 1993 Mazda B2000, B2200, B2600
The wait is finally over!! Our V2 triangulation kit features DOM tube arms, adjustable heim joints for caster adjustment, as well as an optional install kit to make your life much easier!
This kit takes place when removing the factory tension rods when adding air bags, hydraulics, or coil overs.
What’s included:
2 triangulation arms with gussets and adjustable heim joints
2 frame brackets to mount triangulation arms
Grade 8 hardware
Optional shock mounting kit includes - upper shock towers, M12-1.75 lower shock bungs, M12-1.75 hardware ( NOT DESIGNED TO SUPPORT COILOVERS OR HYDRAULICS! )
Optional Installation kit includes - 5/8” all thread, X4 5/8” Nuts, Crush Sleeve
Features:
CNC Plasma cut, CNC Bent
3/16” P+O steel brackets and tabs
1.25” DOM Tube ( .120” wall )
Vehicle Fit:
Nissan D21 / Hardbody 2wd 1986.5 - 1997
!!! OFFROAD USE ONLY, INSTALL AT YOUR OWN RISK !!!
RohdeFab recommends this kit to be installed by an experienced fabricator.
Weather pulling your kid around a car show or throwing a cooler in the tub, This wagon kit allows you to take your boring old radio flyer wagon and slam it on the ground! This frame offers 3 different height positions to best fit your style and the ground your rolling! Built with 11g steel this frame matches the 200lb capacity as the original wagon.
Features:
CNC Plasma Cut, CNC Bent
Made from 11g P+O Steel
DOES NOT INCLUDE WHEELS, TUB, PULL HANDLE!!
Frame kit comes raw, you will need to paint or powder coat to avoid corrosion.
Designed for 10” radio flyer steel wheels
Assembly takes less than 30min and requires minimal hand tools!
200lb weight limit
Adjustable ride height! ( 3/8”, 1”, 1 5/8” )
Optional RF Pull Handle
NOTE: Frame kit is designed around the modern radio flyer classic model #18, if you have an older / off brand wagon you may need to drill new holes in the tub to work with this kit!
Universal trim to fit 8 piece Step notch kit
Features:
CNC Plasma Cut, CNC Bent
3/16” P+O Steel
4 sides, 4 caps
Raw uncoated
Ditch that generic stand with our classy raised dog bowl stand! Our stand features Dimpled paw prints with dog bones, a customizable name tag, and a unique “floating” look for a more modern feel! This is a great stand for your small to medium sized doggys’s. ( more sizes to come )
These include a base to set onto your floor, or you have the option to remove the base and mount directly to a wall for a true “floating” appearance.
Customizable name tag notes:
You must choose the “custom name tag” option
Name must be under 10 characters
Please be sure to double check spelling before submitting your order
Font - Ananda
Features:
18g steel top, 3/16” steel base, .050” aluminum name tag
CNC Plasma Cut
Dimensions: 16.125” wide X 8.125” deep X 6” tall
Dimple died paws and dog bones
What’s included - Stainless hardware, 2 Glass bowls, name tag, bowl stand
SOLD AS BARE STEEL, YOU WILL NEED TO PAINT OR POWDER COAT TO AVOID CORROSION!
THIS STAND IS NON WEIGHT BARRING, EXCESSIVE WEIGHT WILL CAUSE DAMAGE!
1986.5 Nissan Hardbody
205/45/16 (16x6.5)
AirBagged